No difference in slow putting around, no noticeable drivability changes. Got on the fwy and played around a bit and WHOW, what a difference! The car pulls to near Redline like never before, power (mainly torque) is improved everywhere. I launched too hard for my aching clutch and it just slipped to hell. ![]() Getting on the FWY the on ramp lights were on, perfect chance for me to test out 1-3rd gear. I then had my girlfriend jump in the car to to pick up some stuff down the freeway and tested the tune out. I turned off the ignition, turned it back on and checked the Access Port to see what map was loaded. this took all of like 3 seconds and I was a little amazed how fast it was. I did as I think it would be best to return it to stock when I bring the car in for service.Īfter the 30min download I selected to load the 91 octane Stage1 with intake map. After a few ignition key on/offs and unplugs as instructed by the access port it asked if I wanted to download the stock ECU and that it would take around 30min. I made sure all the interior lights were set to off with doors open, rolled down the windows, plugged in the access port and it stated the dongle needed to be updated. I closed the software, unplugged the Access Port and got into my car. I promptly imported them into the Access Port Manager software, plugged in the Access Port and it synced up. I ended up grabbing the valet, Stage 1+ intake 91octane (I'm in CA), and economy maps. Took about 1min or so.Īfter the update was complete I installed the Access Port Manager and the maps I wanted to have loaded. This was easy, (even on a VISTA laptop) just downloaded the firmware updater, ran it, plugged in the unit (had to unplug and replug it once) and boom it started to update. It was not updated to the latest firmware or tunes so I had to do that. I got mine from "PerformanceRacing" here on the board. However, I just wanted to drop my impression for others that may be sitting in the wings for a tuning solution, or a reason to get one. A map file can also be located on your computer by right-clicking on a Map in the list and choosing "Open Map file location.Hey guys, I know a LOT of you already have the Access Port and a lot has been discussed about it.Additional columns can also be displayed in the map search area by right-clicking on any of the columns, and selecting the desired columns to display.If changes to map files happen while Accessport Manager is running, press the Refresh button and the changes will be detected and loaded. These map details and search location are saved even when the software is closed, so searching the same location does not take a long time to load details next time the software is opened.Results will instantly be displayed, even while typing. Perform a text search by typing in the "Search." box or use the drop-down to filter by vehicle. All sub-folders and files will be indexed for searching, and all maps meeting the filter criteria will be displayed in the list. Click the Browse button by the Location box to choose the location to search.This search feature is primarily used by COBB ProTuners that have thousands of customer maps to search through. This will open a new area used for searching through the map descriptions, vendor names, map revisions, vehicle types, and more. Note: Very old V2 Accessport firmware may require selecting "Re-connect" from the main menu on the Accessport itself.Īccessport Manager allows searching through the internal map details of a large number of maps, by clicking the "Search for Maps" button. If you would like to reconnect the Accessport to the computer, simply press "Connect" again. When you're finished managing the files on your Accessport, press the "Eject AP" button to disconnect. It is strongly advised to update to new Accessport firmware whenever Accessport Manager notifies that it is available, because we are constantly improving our products! Accessport Manager will also automatically check for new firmware for your Accessport. Once plugged in, the Accessport will start up and be detected by Accessport Manager, as long as "Automatically connect to Accessport" is checked under Options. ![]() If using a different cable than was supplied with the Accessport, make sure it is data transfer capable and not simply a charging cable. The larger end of the USB cable goes to the computer and the smaller end of the USB cable goes to the Accessport. To update your Accessport with new maps and update firmware, use the supplied USB cable to connect the Accessport to your computer.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |